- Anvil Brewing
- Brewery Controllers
- Brew Stands & Systems
- Brewing Kettles & Hop Filters
- Burners & Accessories
- Blichmann Engineering
- Cam & Groove Fittings
- Conicals & Accessories
- CIP Spray Balls
- Custom Welding
- Fermentor Kits
- Five Star Chemicals
-
Gaskets
- 1/2" & 3/4" Tri Clover Compatible Gaskets
- 1"/1.5" Tri Clover Compatible Gaskets
- 2" Tri Clover Compatible Gaskets
- 2.5" Tri Clover Compatible Gaskets
- 3" Tri Clover Compatible Gaskets
- 4" Tri Clover Compatible Gaskets
- 6" Tri Clover Compatible Gaskets
- 8" Tri Clover Compatible Gaskets
- 10" Tri Clover Compatible Gaskets
- 12" Tri Clover Compatible Gaskets
- Kegging Equipment/Accessories
- Modular Return System
- O-Rings
- Penguin Chillers
- Pumps
- Quick Disconnect Fittings
- RIMS Tubes & Electric Brewing
- Tapcooler Bottle Filler & Accessories
- Thermowells
- Stainless Tubing
- Threaded Fittings
- Temperature Probe Components
- Temperature Sensors
-
Tri Clamp Compatible Fittings
- Tri Clover Compatible X NPT Adapters
- Tri Clover Compatible X Hose Barb
- Tri Clover Compatible X Cam & Groove
- Tri Clover Compatible X Quick Disconnect
- Tri Clover Compatible X Beer Thread
- Tri Clover Compatible X Garden Hose Thread
- Tri Clover Compatible X Corny Post Thread
- Tri Clover Compatible X Compression Adapters
- Tri Clover Compatible X Flare Adapters
- Tri Clover Compatible X BSP Fittings
- Tri Clover Compatible Clamps
- Tri Clover Compatible Gaskets
- Tri Clover Compatible Valves
- Tri Clover Compatible Ferrules
- Tri Clover Compatible Caps
- Tri Clover Compatible Elbows
- Tri Clover Compatible Tees
- Tri Clover Compatible Wyes
- Tri Clover Compatible Crosses
- Tri Clover Compatible Sight Glasses
- Tri Clover Compatible Concentric Reducers
- Tri Clover Compatible Eccentric Reducers
- Tri Clover Compatible Cap-Style Reducers
- Tri Clover Compatible Extension Tubes/Spools
- Tri Clover Compatible Check Valves
- Tri Clover Compatible PRV Tank Breathers
- Tri Clover Compatible Pressure Gauges
-
Shop By Size
- 1/2"-3/4" Tri Clover Compatible Fittings
- 1"/1.5" Tri Clover Compatible Fittings
- 2" Tri Clover Compatible Fittings
- 2.5" Tri Clover Compatible Fittings
- 3" Tri Clover Compatible Fittings
- 4" Tri Clover Compatible Fittings
- 6" Tri Clover Compatible Fittings
- 8" Tri Clover Compatible Fittings
- 10" Tri Clover Compatible Fittings
- 12" Tri Clover Compatible Fittings
- Wort Strainers
- Tubing/Hose
- Weldless Fittings
- Merch
- Clearance
12" Heat Shield / Burner Mount
HS12
12" Heat Shield and Burner Mount
These 12" diameter X 4" tall burner mount/heat shields are made to fit a the 12" bay of a typical Brutus 10 type single tier stand. They have mounting holes to accommodate our BURN10 Banjo-Style burner as well as the Bayou Classic BG14 Banjo Burner.
The 12" design will require 1/2" longer screws for your burner and leaves 1/2" between the mounting lug and the shield itself. The new design is rolled but no longer spot welded, giving you a little flexibility to make for minor dimension corrections without squeezing the ring out of shape. The seam is made to be at the rear of the ring. There are 3 heights of mounting holes for the burner that are offset to rotate the burner about 30º to tuck it under the stand just a little while still allowing it to be accessible. It also gets it out from being directly under the valve connections or your kettles (assuming of course you have them directly forward).
The other new feature allows you to "unfold" the top 2" X 180º of the back half of the ring. One of the issues I've run into in R&D for stands and burner mounts is getting the exhaust gas to vent rather than collect under the kettle and choke the flame. It's a particular problem with these large burners. Mounting the heat shield lower or standing the kettle higher is one way to fix the issue, but then a lot of heat wash comes forward towards your valves, hoses and sensor wires. If you design your stand so the rear longitudinal support is 2" lower than the cross/kettle supports, the exhaust gas will naturally vent to the rear, allowing the burner to breathe better and keep the front cooler. This heat shield/mount is already cut so you can unfold the top 2" of it and bend it towards the rear, offering a heat shield for the cross supports and better venting to the back of the stand. This only works of you have the rear cross member lower or relieved.
Made from heavy duty 18 gauge 304 stainless.
Customer reviews
-
BrewdogbrewingsystemsLLCDec 31, 1969, 16:00The burn shield looks great but doesnt fit my bayou classic brand BG14. If i do use the stock mounting holes the whole thing warps and gets lop sided. Maybe this worked better on other brands but not the standard bayou brand.
-
aaron bDec 31, 1969, 16:00Nice shields. One odd thing about them however is that the mounting holes seem to be drilled at random locations relative to the foldout on each unit. Do to this it's impossible to have the foldout facing the same direction while keeping the burner stems the same direction. Not a huge deal but would have been nice to know before welding to my rig!